PhotoRobot Safety

Safety is the precondition for everything else in PhotoRobot Academy. Before workspace configuration, capture workflows, mechanical assembly, or integration, you read this module. The content is not long — but failure to internalize it can cost injury, equipment damage, or both.

1. Why this module is mandatory

PhotoRobot devices are industrial-grade equipment. They move under power, carry significant weight, integrate high-intensity light sources, and connect to mains electrical supply. The hazards are real — but every hazard documented here has a known, simple mitigation.

This module gives you the safety baseline. Specific devices add their own safety notes (laser positioning, ceiling clearances, mannequin handling) — those live with each device’s installation manual on photorobot.com.

The fundamental rule: if you are unsure, stop. Then call an authorized authority. Hesitation in safety is correct.

2. Roles & responsibilities

If you are not in the matching role for a task, you are not authorized to perform it.

3. Installation safety

The first installation after delivery is exclusively the authority’s job. Customer staff may observe and learn — that participation is encouraged in Academy practice — but the authority is responsible for completion.

Universal precautions during any installation or relocation:

• Inspect packaging and the device for damage. Do not install or use a damaged device.
• Remove transit bolts. These secure moving parts during shipping. Failure to remove can damage the motor on first power-up.
• Wear safety gloves. PhotoRobot machines are heavy — they pinch and crush. Gloves reduce both injury and slippage.
• Flat, stable, clean floor. The installation site must be level. Use the device’s leveling feet to fine-tune flatness.
• Air circulation around the device. Do not box the device in. Heat needs to dissipate.
• Indoor only. PhotoRobot devices are not designed for outdoor exposure (humidity, dust, temperature swings, direct sun).
• Walkable clearance around the device. Operators must be able to move around the device without obstacle — both for daily work and for emergency response.

For mechanical assembly specifics — bolt torque, alignment, calibration — see the device-specific installation manual and module B13 Mechanical assembly (hardware specialist track).

4. Electrical safety

PhotoRobot devices connect to mains electrical supply. Treat them as you would any industrial electrical equipment.

• Grounding is mandatory. The device must be connected to a properly grounded shockproof socket. Never bypass the ground pin.
• Voltage compatibility. Before connecting, verify the electrical information on the device’s rating plate matches your installation site’s mains supply. If they do not match, contact an electrician. Some models have a voltage selector switch (2.5A / 5A) — selecting wrong burns the unit.
• Cable inspection. If the supply cord is damaged, replace it before use. A damaged supply cord must be replaced by an authority to avoid hazard.
• Plug handling. Connect the mains plug only at the end of installation. Always keep the mains plug accessible after installation — you need to be able to disconnect quickly if something goes wrong.
• Wet hands forbidden. Never touch the mains cable or plug with wet hands. Wet hands + mains = lethal.
• Push the switch first, then unplug. To disconnect, always press the mains switch at the Control Unit first, then pull the plug. Never pull the cable to disconnect — repeated cable-pull damages the plug and cord internals.
• Stay back when powered. Do not approach the device when it is moving, or when it is powered up and stationary. Powered-stationary still means it can move at the next command.

Working area awareness. Every powered device has a defined working envelope. For example, the Robotic Arm V8 has a 32 cm elevator range and a 0-90° swing arm range. Operators must know the envelope of each device they work with and keep themselves and bystanders outside it during operation. Device-specific working areas are in each installation manual.

5. Operation safety

• Industrial environment only. PhotoRobot devices are designed for industrial / production environments — not for amateur home studios. The protective measures and ratings assume this context.
• No flammables nearby. Lights run hot. Do not place flammable items, solvents, or aerosols near or on the device.
• No touching during movement. Pinch and crush risk applies anywhere a moving part can contact a hand. Stay back until the sequence has finished and the device has stopped.
• Risk awareness. When in use, possible risks include: injury, electrical shock, fire, burns, equipment damage. None are random — all are preventable by following procedure.

If something feels wrong — unusual noise, smell, heat, movement — stop the device using the mains switch on the Control Unit, then call support. Do not attempt diagnosis while the device is powered.

6. Cleaning & user maintenance

• Deactivate first. Before any maintenance or cleaning, deactivate the device and disconnect the mains plug from the socket. Disconnected, not just switched off.
• No water spray, no steam. These ingress moisture into electronics. Damp soft cloth only.
• Neutral detergent only. No abrasive cleaners, no scrub pads, no solvents, no metal objects against the surface.
• No children unsupervised. Cleaning and user maintenance must not be performed by children without supervision.

Beyond surface cleaning, all maintenance is service. Service is for authorized authorities only (Section 2).

7. Children & vulnerable adults

PhotoRobot devices can be used by children aged 8+, and by adults with reduced physical / sensory / mental capabilities or lacking operational knowledge, only if they are under supervision or have received specific safety instructions and the operator understands the hazards involved.

• Children under 3: keep away from the device unless under constant adult supervision.
• Children at play: never allow the device to become a toy. Play with industrial equipment ends with injury.
• Operator responsibility: if your studio operates near public or family spaces, you are responsible for keeping unauthorized persons out of the working envelope.

This is the section every customer reads and signs off on before commissioning — not a formality, a deliberate barrier.

8. Information labels & device-specific safety

Every powered PhotoRobot device carries information labels. These contain:

• Model identification (machine type, serial number)
• Voltage / amperage rating (must match your mains supply)
• Power consumption
• Manufacturer identification
• Compliance marks (CE, etc.)

Read the labels on your device before installation, electrical connection, and any service. If a label is unreadable due to wear, request a replacement — never operate a device whose ratings cannot be verified.

The latest Control Unit (G7) is a separate-but-integral component shared across these systems:

• PhotoRobot Centerless Table
• Robotic Turntable
• Cube V5 / V6
• MultiCam
• Robotic Arm V8
• Turning Platform
• Virtual Catwalk
• Carousel 3000 / 5000

The Control Unit is built-in to: PhotoRobot Case 850, C850 & C1300, Cube Compact, Frame. Some installations use older Control Unit revisions (G5 or G6) instead of G7 — the safety principles apply identically across revisions.

Device-specific information labels (Case 850, C850 / C1300, Cube Compact, Carousel 3000, Carousel 5000, Laser Box VI, MultiCam IV, …) are documented on the manufacturer’s safety reference. Always cross-check before service.

9. When to stop

The safety culture in a PhotoRobot studio comes down to one habit: stopping when uncertain.

You stop when:

• Something on the device feels, sounds, or smells wrong.
• An installed component does not match its label.
• You cannot identify a part or its function.
• The procedure you are about to perform is outside your role’s authorization.
• Someone unauthorized is in the working envelope.
• You cannot remember a step and the manual is not at hand.

Stopping costs minutes. Continuing past one of these triggers can cost weeks of equipment downtime or worse.

10. For full reference

This module is a brief operational summary. The canonical, always-up-to-date safety reference on photorobot.com is:

• PhotoRobot Safety Information & Instructions — full safety reference including device-specific information labels (Case 850, C850 / C1300, Cube Compact, Carousel 3000, Carousel 5000, Laser Box VI, MultiCam IV, Control Unit G7), child & vulnerable adult safety, installation / electrical / use / service procedures.

When in any doubt during installation, operation, or service — open the canonical manual. The detail there overrides the summary here.

Module check

When you’re ready, take the module knowledge check for this module. It’s not graded for certification — it’s for you and your instructor to identify any gaps before moving on.

→ Take the module check  ·  5 questions, immediate feedback